TME-EXP-ISO-COM8-R1V0 Revision 1.0 / February 14 ©LiPPERT Adlink Technology GmbH Hans-Thoma-Str. 11 D-68163 Mannheim http://www.adlinktech.com E
TME-EXP-ISO-COM8-R1V0 Rev 1.0 5 (24) Mechanical Dimensions (L x W) 165 mm x 115 mm Height max. 17 mm on top side above PCB max. 12 mm on bott
TME-EXP-ISOMecFront Side vSystem O-COM8-R1V0chanical viview view m stack-up viNote0 iew iew with Hurre For detaileddepartmenticane-QM57 ad mechanic
TME-EXP-ISO-COM8-R1V0 Rev 1.0 7 (24) Metrics on Top The connectors' pin 1 is marked with an arrow.
TME-EXP-ISO-COM8-R1V0 Rev 1.0 8 (24) Getting Started 1.4 Connector Locations Top The connectors' pin 1 is marked with an arrow. Port
TME-EXP-ISO-COM8-R1V0 Rev 1.0 9 (24) Bottom PC/104PlusPCI/104Express
TME-EXP-ISO-COM8-R1V0 Rev 1.0 10 (24)
TME-EXP-ISO-COM8-R1V0 Rev 1.0 11 (24) 1.5 Jumper Locations The connectors' pin 1 is marked with an arrow. Port 8 X4Port 7 X5Port 6 X8
TME-EXP-ISO1.6 LED Onbothe wO-COM8-R1V0indicatoroard there is aworking state o0 rs a yellow LED tof the OXPCIethat shows e chip. Rev 1.012 (2 4)
TME-EXP-ISO-COM8-R1V0 Rev 1.0 13 (24) 1.7 Hardware Setup Caution Be sure to observe the EMC security measures. Make sure you are always at t
TME-EXP-ISO-COM8-R1V0 Rev 1.0 14 (24) 1.8 Software Setup Driver packages are available for the following operating systems: Linux Window
Technical Manual EXP-ISO-COM8 LiPPERT Document: TME-EXP-ISO-COM8-R1V0 Revision 1.0 Copyright © 2009 LiPPERT Adlink Technology GmbH, All rights reser
TME-EXP-ISO-COM8-R1V0 Rev 1.0 15 (24) 2 Module Description 2.1 OXPCIe958 The device combines a fully integrated, single-lane PCI Express end-po
TME-EXP-ISO-COM8-R1V0 Rev 1.0 16 (24) Pin RS232 RS485 Pin RS232 RS485 1 DCD Not used2 DSR RXD+ 3 RXD RXD- 4 RTS TXD+ 5 TXD
TME-EXP-ISORS48ConneUse 2The RFor se Whenare te(e.g. RAdditpulledorder COM8It is re Pin 1 3 5 O-COM8-R1V085-Selectionector type 2 mm jumper
TME-EXP-ISO-COM8-R1V0 Rev 1.0 18 (24) 2.2 PC/104-Plus Bus Connector The PC/104-plus bus is not used on that module. The mounted connector forwar
TME-EXP-ISO-COM8-R1V0 Rev 1.0 19 (24) Pin A B C D 26 n.c. n.c. GND n.c. 27 n.c. n.c. n.c. GND 28 GND n.c. n.c. n.c. 29 n.c. n.c
TME-EXP-ISO-COM8-R1V0 Rev 1.0 20 (24) 2.3 PCI/104 Express Bus Interface The EXP-ISO-COM8 uses x1 link of the PCI/104-Express bus. According to t
TME-EXP-ISO-COM8-R1V0 Rev 1.0 21 (24) The following table shows the shifting of PCI Express links from top to bottom connector. The rest of not
TME-EXP-ISO-COM8-R1V0 Rev 1.0 22 (24) Bottom PCI/104-Express Connector Connector Type: Samtec ASP-129646-03 The blue highlighted signals are
TME-EXP-ISO-COM8-R1V0 Rev 1.0 23 (24)
TME-EXP-ISO2.4 PortEach sADuMgalvanGND FeatuADu Hig SO 25 VIOO-COM8-R1V0t Isolationserial port is M5401 and ADnic isolated. Iand Data. ures uM
TME-EXP-ISO-COM8-R1V0 Rev 1.0 i Table of Contents 1 Overview 11.1 Introduction ...
TME-EXP-ISO-COM8-R1V0 Rev 1.0 Appendix A Appendix A, Contact Information Headquarters LiPPERT ADLINK Technology GmbH Hans-Thoma-Straße 11 681
TME-EXP-ISO-COM8-R1V0 Rev 1.0 Appendix B Appendix B, Additional Information B.1 Additional Reading Datasheet of the OXPCIe958 at http://www.
TME-EXP-ISO-COM8-R1V0 Rev 1.0 Appendix C Appendix C, Getting Help Should you have technical questions that are not covered by the respective
TME-EXP-ISO-COM8-R1V0 Rev 1.0 Appendix D Appendix D, Revision History Filename Date Edited by Change TME-EXP-ISO-COM8-R0V0.doc 2009-12-10
TME-EXP-ISO-COM8-R1V0 Rev 1.0 ii 2 Module Description 152.1 OXPCIe958 ...
TME-EXP-ISO-COM8-R1V0 Rev 1.0 iii Acronyms CTS Clear To Send DCD Data Carrier Detect DSR Data Set Ready DTR Data Terminal Ready FIFO
TME-EXP-ISO-COM8-R1V0 Rev 1.0 1 (24) 1 Overview 1.1 Introduction The EXP-ISO-COM8 is an Add-on Module conforming to the EPIC Express Specificat
TME-EXP-ISO-COM8-R1V0 Rev 1.0 2 (24) Block Diagram
TME-EXP-ISO-COM8-R1V0 Rev 1.0 3 (24) 1.2 Ordering Information EXP-ISO-COM8 Models Order number Description 714-0002-10 EXP-ISO-COM8 with galva
TME-EXP-ISO-COM8-R1V0 Rev 1.0 4 (24) 1.3 Specifications Electrical Specifications Supply voltage +5 V DC Rise time < 10 ms Supply voltage
Kommentare zu diesen Handbüchern