Adlink ASD26-MA2 Series Bedienungsanleitung

ASD26-MLC/MA2 Series 2.5" SATA 6 Gb/s & SATA 3 Gb/s Solid State Drive Specification Revision: 1.03 Date: December 6, 2012 Part N

1.2.12. Reliability Parameter Value Mean Time between Failure (MTBF) > 1,500,000 hours Power on/off cycles 50,000 cycles Minimum useful life

1.2.14. Electromagnetic Immunity: Electromagnetic Immunity tests assume the SSD is properly installed in the representative host system. The drive o

1.2.17. Part Numbers: Standard Operating Temperature Range: 0°C to 70°C Product Name Part No. ASD26-MLC32G-CT 92-99059-5510 ASD26-MA2032-ET 92-9905

1.4 Product Image Specification 13

1.5 Mechanical Drawing: Dimensions: 100.0 x 69.8mm x 9.5 mm (L x W x H) 14 Specification

1.6 Architecture The ASD26-MLC series 2.5" SATA Solid State Drive (SSD) utilizes a cost effective system-on-chip (SoC) design to provide a full

2 Pin Locations and Signal Descriptions 2.1 Pin Locations The data and power connector pin locations of the ASD26-MLC series 2.5" SATA SSD are a

Power Connector: Name Type Description P1 V33 3.3V Power P2 V33 3.3V Power P3 V33 3.3V Power, Pre-change P4 GND P5 GND P6 GND P7 V5 5V

3 ATA Command Sets 3.1 ATA Command The ASD26-MLC series 2.5" SATA SSD supports all the mandatory ATA commands defined in the ATA/ATAPI-8 specif

3.1.2 Identify Device Data The following table details the sector data returned after issuing an IDENTIFY DEVICE command. Word F=Fixed V=Variable X=

Document History Revision Date Changes 1.00 2012/02/02 Initial Release 1.01 2012/04/02 Add ASD26-MLC64G-CT data 1.02 2012/07/02 Add ASD26-MLC32G-C

F=Fixed V=Variable Word Default Value Description X=Both 64 F 0007h Multi-word DMA modes supported/selected 65 F 0003h PIO modes supported 66

F=Fixed V=Variable Word Default Value Description X=Both 95 V 0h Vendor’s recommended and actual acoustic management value 96 F 0h Stream Minim

F=Fixed V=Variable Word Default Value Description X=Both 235 F 0h Reserved 236-254 0001h Reserved 255 02A0h Reserved 236-254 F 0h Res

3.3 Security Mode Feature Set The ASD26-MLC series 2.5" SATA SSD supports the Security Mode command set, which consist of ．SECURITY SET PASSWO

Subcommand Code LBA Low value SMART ATTRIBUTE VALUES (READ DATA) D0h READ ATTRIBUTE THRESHOLDS D1h ENABLE/DISABLE ATTRIBUTE AUTOSAVE D2h SAVE

．READ NATIVE MAX ADDRESS ．FLUSH CACHE EXT ．READ DMA EXT ．READ NATIVE MAX ADDRESS EXT ．READ SECTOR(S) EXT ．READ VERIFY SECTOR(S) EXT ．SET MAX ADDRESS

4 SATA Command Sets 4.1 SATA Command The SATA 3.0 Specification is a super set of the ATA/ATAPI-8 specification with regard to supported commands. Th

5 References This document references standards defined by a variety of organizations as listed below. Date Title Location Dec 2008 VCCI http://

6 Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe Distri

LiPPERT ADLINK Technology GmbH Address: Hans-Thoma-Strasse 11, D-68163, Mannheim, Germany Tel: +49-621-43214-0 Fax: +49-621 43214-30 Email: e

Copyright 2012 ADLINK Technology, Inc. Disclaimer The information in this document is subject to change without prior notice in order to improve re

Table of Contents 1 Introduction ...5 1.1 Overview...

1 Introduction 1.1 Overview The ASD26-MLC (ASD26-MLC & ASD26-MA2) series 2.5" SATA Solid State Drive (SSD) delivers leading performance in

1.2.3. Flash: Multi-Level Cell (MLC) component with Toggle-Mode (24nm) 1.2.4. Band Performance (CrystalDiskMark) Capacity Access Type MB/s Sequent

1.2.5. Read and Write IOPS (IOMETER) Capacity Access Type IOPS 4K Read (IOPS) 40,000 (SATA 6 Gb/s) 4K Write (IOPS) 19,000 (SATA 6 Gb/s) 32 GB &q

1.2.6. Power On to Ready: Type Average Latency Power on to Ready 1s Table 4: Latency Specifications Notes: 1. Write cache enabled 2. Device measur

1.2.10. Power Consumption Capacity Description Min Max Unit 32 GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V 64 GB Operating voltage for