ASD26-HA2 Series 2.5" SATA 3 Gb/s Solid State Drive Specification Revision: 1.00 Date: December 6, 2012 Part Number: 50-1Z139-1000
1.2.14. Electromagnetic Immunity: Electromagnetic Immunity tests assume the SSD is properly installed in the representative host system. The drive o
1.3 Functional Block Diagram SATA Host Interface NAND Flash Array Flash Memory Controller 1.4 Product Image Specificati
1.5 Mechanical Drawing: Dimensions: 100.0 x 69.8mm x 9.5 mm (L x W x H) 12 Specification
1.6 Architecture The ASD26-HA2 series 2.5" SATA 3 Gb/s Solid State Drive (SSD) utilizes a cost effective system-on-chip (SoC) design to provide
2 Pin Locations and Signal Descriptions 2.1 Pin Locations The data and power connector pin locations of the ASD26-HA2 series 2.5" SATA 3 Gb/s SS
Power Connector: Name Type Description P1 V33 3.3V Power P2 V33 3.3V Power P3 V33 3.3V Power, Pre-change P4 GND P5 GND P6 GND P7 V5 5V
3 ATA Command Sets 3.1 ATA Command The ASD26-HA2 series 2.5" SATA 3 Gb/s SSD supports all the mandatory ATA commands defined in the ATA/ATAPI-8
3.1.2 Identify Device Data The following table details the sector data returned after issuing an IDENTIFY DEVICE command. Word F=Fixed V=Variable X=
F=Fixed V=Variable Word Default Value Description X=Both 64 F 0007h Multi-word DMA modes supported/selected 65 F 0003h PIO modes supported 66
F=Fixed V=Variable Word Default Value Description X=Both 95 V 0h Vendor’s recommended and actual acoustic management value 96 F 0h Stream Minim
Document History Revision Date Changes 1.00 2012/12/06 Initial Release 2 Specification
F=Fixed V=Variable Word Default Value Description X=Both 235 F 0h Reserved 236-254 0001h Reserved 255 02A0h Reserved 236-254 F 0h Res
3.3 Security Mode Feature Set The ASD26-HA2 series 2.5" SATA 3 Gb/s SSD supports the Security Mode command set, which consist of .SECURITY SET
Subcommand Code LBA Low value SMART ATTRIBUTE VALUES (READ DATA) D0h READ ATTRIBUTE THRESHOLDS D1h ENABLE/DISABLE ATTRIBUTE AUTOSAVE D2h SAVE
3.6 48-Bit Address Command Set The ASD26-HA2 series 2.5" SATA 3 Gb/s SSD supports the Host Protected Area command set, which consists of .READ N
4 SATA Command Sets 4.1 SATA Command The SATA 3.0 Specification is a super set of the ATA/ATAPI-8 specification with regard to supported commands. Th
5 References This document references standards defined by a variety of organizations as listed below. Date Title Location Dec 2008 VCCI http://
6 Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe Distri
LiPPERT ADLINK Technology GmbH Address: Hans-Thoma-Strasse 11, D-68163, Mannheim, Germany Tel: +49-621-43214-0 Fax: +49-621 43214-30 Email: e
Copyright 2012 ADLINK Technology, Inc. Disclaimer The information in this document is subject to change without prior notice in order to improve re
Table of Contents 1 Introduction ...5 1.1 Overview...
1 Introduction 1.1 Overview The ASD26-HA2 series 2.5" SATA 3 Gb/s Solid State Drive (SSD) delivers leading performance in an industry standard
1.2.4. Band Performance (CrystalDiskMark) Capacity Access Type MB/s Sequential Read Up to 190 (SATA 3 Gb/s) Sequential Write Up to 100 (SATA 3 G
1.2.6. Power On to Ready: Type Average Latency Power on to Ready 1s Table 4: Latency Specifications Notes: 1. Write cache enabled 2. Device measur
1.2.10. Power Consumption Capacity Description Min Max Unit 16 GB Operating voltage for 5V (+/- 5%) 4.75 5.25 V 32 GB Operating voltage for
1.2.13. Shock and Vibration: Item Mode Timing/Frequency Max Non-operating At 0.5 msec 1500G Non-operating At 1 msec 1500G Shock1 Non-operating
Kommentare zu diesen Handbüchern