Adlink Express-LPC Bedienungsanleitung PDF herunterladen (Seite 61)

Page 61Express-IA533 User’s Manual Page 61Express-IA533 User’s ManualExpress-LPC User’s Manual Page 61

Power Management/APM

Set this value to Enable or Disable Power Management/APM (Advanced Power

Management) features.

Power Button Mode

This option sets the function of the power button. Options: On/Off, Suspend.

Suspend Time Out

This option specifies the length of time the system waits before it enters suspend mode. The

options are Disabled, 1 Min, 2 Min, 4 Min, 8 Min, 10 Min, 20 Min, 30 Min, 40 Min, 50 Min,

and 60 Min.

8.4.2 APM Configuration

Select the Advanced tab from the setup screen to enter the APM Configuration Setup screen.

You can display a Power Management/APM Setup option by highlighting it using the <

Arrow > keys.

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 85 86

Express-LPC 1
Revision History 2
Table of Contents 3
Disclaimer 5
Environmental Responsibility 5
Trademarks 5
Conventions 6
1 Introduction 7
2 Specifications 8
2.3 Audio 9
2.5 Multi I/O 9
2.7 Super I/O 9
2.8 Power Specifications 10
3 Functional Diagram 11
4 Mechanical Dimensions 12
5.1 COM Express 13
Type 2 compatible pinout 13
5.3 Pin Definitions 14
Pin Definitions (cont’d) 15
5.4 Signal Descriptions 16
Signal Descriptions (cont’d) 17
6 Embedded Functions 25
6.2 GPIO 26
6.3 Hardware Monitoring 27
7 System Resources 28
7.3 Legacy I/O Map 29
Legacy I/O Map (cont’d) 30
PIC Mode 30
APIC Mode 31
7.6 PCI Interrupt Routing Map 32
8 BIOS Setup Utility 33
8.1.1 Main Setup Menu 34
8.1.2 Navigation 35
8.2 Main Setup 37
8.3 Advanced BIOS Setup 38
8.3.1 CPU Configuration 39
CPU Configuration Settings 39
Max CPUID Value Limit 39
8.3.2 Chipset Configuration 41
DRAM Frequency 41
Configure DRAM Timing by SPD 41
APIC ACPI SCI IRQ 41
Internal Graphics Mode Select 42
DVMT Mode Select 42
8.3.4 IDE Configuration 44
IDE Configuration Settings 44
ATA/IDE Configuration 44
Legacy IDE Channels 44
Hard Disk Write Protect 45
IDE Detect Time Out 45
ATA(PI)80Pin Cable Detection 45
8.3.5 AHCI Configuration 45
AHCI Ports 46
Onboard LAN Boot ROM 47
HD Audio Controller 47
SMBus Controller 47
SuperIO Configuration Screen 48
Floppy A 48
OnBoard Floppy Controller 48
Serial Port1 Address 49
Serial Port2 Address 49
Parallel Port Address 49
Parallel Port Mode 49
8.3.7 USB Configuration 50
USB Configuration Settings 50
Parallel Port IRQ 50
Active State Power-Management 53
PCIE Ports 0-3 Configuration 53
PCIE High Priority Port 53
Remote Access 55
Serial Port Number 55
Remote Access Configuration 55
Option Description 56
8.3.11 Trusted Computing 57
Execute TPM Command 57
8.4 Power Management 58
ACPI Aware O/S 59
ACPI Version Features 59
ACPI APIC Support 59
USB Device Wakeup from S3/S4 59
AMI OEMB Table 59
Suspend mode 60
Headless mode 60
Restore on AC Power Loss 60
ACPI OS Shutdown Mode 60
Power Management/APM 61
Power Button Mode 61
Suspend Time Out 61
8.4.2 APM Configuration 61
Video Power Down Mode 62
Throttle Temperature 63
Throttle Duty 63
Critical Temperature 63
8.5 Boot Setup 64
Quick Boot 65
Quiet Boot 65
AddOn ROM Display Mode 65
Bootup Num-Lock 66
PS/2 Mouse Support 66
Wait for ‘F1’ If Error 66
Hit ‘DEL’ Message Display 66
Interrupt 19 Capture 66
Boot Device Priority 67
Boot Device Groups 67
8.6 Security Setup 68
8.6.3 Change User Password 70
8.6.4 Clear User Password 70
8.7 Exit Menu 71
Discard Changes 72
Load Optimal Defaults 72
Load Failsafe Defaults 72
Viewing BIOS Checkpoints 73
9.3 POST Code Checkpoints 76
POST Code Checkpoints cont’d: 77
9.5 DIM Code Checkpoints 78
9.6 ACPI Runtime Checkpoints 79
9.7 Boot Block Beep Codes 80
9.8 POST BIOS Beep Codes 80
Important Safety Instructions 82
Getting Service 84

Kommentare zu diesen Handbüchern

Keine Kommentare

Adlink Express-LPC Bedienungsanleitung Seite 61

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Adlink Express-LPC