Adlink cPCIS-ET1100 Series Bedienungsanleitung

cPCIS-1100 Series 3U Height Subsystems for CompactPCI Modules User’s Guide

4 • Introduction This page intentionally left blank.

Getting Started • 5 2 Getting Started In this chapter, we will describe the unpacking procedure of the sub-system and CompactPCI board and power suppl

6 • Getting Started System slots have obvious indicators (e.g. red card guide rail, triangle mark enclosing the slot number on the backplane, etc

Getting Started • 7 CompactPCI Card Installation/Removal Procedure 1. Place the sub-system on a level surface or rackmount it. Remove the blanking p

8 • Getting Started To remove the module, press the release button (if necessary), and reverse steps 1 through 5 above. 2.3 RTM (Rear T

Getting Started • 9 The installation and removal procedures for a RTM are the same as those for CompactPCI boards. Because they are shorter than front

10 • Getting Started This page intentionally left blank.

Backplane • 11 3 Backplane In this chapter, we will describe the backplanes for the cPCIS-1100 Series subsystems. The following table specifies the b

12 • Backplane Peripheral slots: 7 Peripheral Slots Rear I/O: P2 rear I/O with AB-type shroud (optional) Power Connectors: ATX connector x2, DC screw

Backplane • 13 cBP-3208[R] Rear View 1 - P2 Optional Rear I/O: 2 - P2 to 8 - P2

Revision History Revision Release Date Description of Change(s) 1.00 March 12, 2013 Preliminary release Manual Rev.: 1.00 Prelimina

14 • Backplane Pin Assignment ¾ [1 – P1] System Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND24 GND AD[1] +5V V(I/O)

Backplane • 15 ¾ [1 – P2] System Slot Pin Z A B C D E F 22 GND GA4 GA3 GA2 GA1 GA0 GND21 GND CLK6 GND NC NC NC GND20 GND CLK5 GND NC NC NC

16 • Backplane ¾ [2 – P1] / [8 – P1] Peripheral Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND 24 GND AD[1] +5V V(I/O)

Backplane • 17 ¾ CN1 / CN2 – ATX Power Connector Pin Signal Pin Signal 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON_L 5 GND 15 GND

18 • Backplane cBP-3206[R] Backplane The cBP-3206[R] is a 3U CompactPCI 32-bit backplane with optional rear I/O (designated by an “R” suffix). The cP

Backplane • 19 Mechanical Drawing cBP-3206[R]Rear ViewcBP-3206[R]Front View1 - P21 - P16 - P26 - P1CN1 CN2 JP8 - JP101 - P2 Opt. Rear I/O: 2 - P2

20 • Backplane Pin Assignment ¾ [1 – P1] System Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND24 GND AD[1] +5V V(I/O)

Backplane • 21 ¾ [1 – P2] System Slot Pin Z A B C D E F 22 GND GA4 GA3 GA2 GA1 GA0 GND21 GND CLK6 GND NC NC NC GND20 GND CLK5 GND NC NC NC

22 • Backplane ¾ [2 – P1] – [6 – P1] Peripheral Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND 24 GND AD[1] +5V V(I/O)

Backplane • 23 ¾ CN1 / CN2 – ATX Power Connector Pin Signal Pin Signal 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON_L 5 GND 15

Table of Contents • iii Table of Contents How to Use This Manual...v 1 Introduction ...

24 • Backplane 3.2 cBP-3061 Power Backplane The cBP-3061 is a PICMG 2.11 CompactPCI 3U 47-pin power backplane for one power module. It is used by th

Backplane • 25 Pin Assignment ¾ CN1 – Power Sense Connector Pin # Signal Name 1 V1_Sense 2 GND_S 3 V2_Sense 4 V3_Sense 5 NC ¾ CN2 – Power Sense

26 • Backplane ¾ CN4 – Modular Power 47P Connector Pin Signal Pin Signal 47 ACL/-DC IN 31 GA2 46 ACN/+DC IN 30 V1 SENSE 45 CGND 29 V1ADJ 4

Backplane • 27 ¾ CN7 –AC/DC in Let Connector Pin # Signal Name 1 ACN/DC+ 2 ACL/DC- 3 CGND ¾ CN8 – IPMB Connector Pin # Signal Name 1 IPMB_SCL

28 • Backplane 3.3 cBP-3062A Power Backplane The cBP-3062A is a PICMG 2.11 CompactPCI 3U 47-pin power backplane for two power modules. It is used by

Backplane • 29 Pin Assignment ¾ CN1 / CN2 – Modular Power 47P Connector Pin Signal Pin Signal 47 ACL/-DC IN 31 GA2 46 ACN/+DC IN 30 V1 SENSE

30 • Backplane ¾ CN5 – Power Sense Connector Pin # Signal Name 1 V1_Sense 2 GND_S 3 V2_Sense 4 V3_Sense 5 NC ¾ CN6 –Connector Pin # Signal Name

Backplane • 31 ¾ CN9 / CN10 – ATX Power Connector Pin Signal Pin Signal 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON_L 5 GND 15

32 • Backplane This page intentionally left blank.

Power Supply Unit • 33 4 Power Supply Units The cPCIS-1100 Series subsystems are equipped with either the Zippy Technology Corp. PS2 HG2-6400P industr

iv • Table of Contents Output Characteristics...34 4.2 CompactPCI: cPS-H325/AC...

34 • Power Supply Unit Input Characteristics • Voltage: 90 – 240 VAC Full Range • Frequency : 47 ~ 63 HZ • Input Current: 8.0 A ( RMS ) FOR 115

Power Supply Unit • 35 4.2 CompactPCI: cPS-H325/AC Features • 250W 3U x 8HP Eurocard package • Meets IEC1000-3-2 harmonic correction • Internal OR

36 • Power Supply Unit • Dielectric Withstand: Meets IEC950 regulation • EMI: Meets EN55022 / FCC Class A • Hold-up Time: 5mS after power fail sig

Power Supply Unit • 37 4.3 CompactPCI ETT PSU: cPS-P325/AC Features • 250W 3U x 8HP Eurocard package • Meets EN 61000-3-2 active power factor corre

38 • Power Supply Unit • Power Fail Signal: available at [FAL#] pin • Status LED: <green> means valid input voltage; <amber> means a cr

Power Supply Unit • 39 o Over Current Protection: Installed at each rail. o Overload Protection: Fully protected against output overload or short ci

40 • Power Supply Unit This page intentionally left blank.

Specifications • 41 5 Specifications 5.1 Features Standard 19” Rack-mount 3U CompactPCI form factor (3U height). Board Space: Supports both front and

42 • Specifications 5.3 Environmental Operating Temperature: 1. cPS-H325/AC: 0°C ~ +50°C ; 2. cPS-P325/AC: -25°C ~ +50°C (Up to 70°C but will have

Important Safety Instruction • 43 Important Safety Instructions Read and follow all instructions marked on the product and in the documentation before

How to Use This Manual • v How to Use This Manual This manual is designed to help you use the cPCIS-1100 3U CompactPCI Sub-system. It is divided into

44 • Important Safety Instruction If one of the following situations arises, get the equipment checked by a service personnel: A. The power cord or

vi • Introduction This page intentionally left blank.

Introduction • 1 1 Introduction 1.1 Product Definition The cPCIS-1100 Series Subsystems are rack mountable, 3U in height, and designed for 3U CompactP

2 • Introduction 1.2 Mechanical Drawing

Introduction • 3 1.3 Configurations The cPCI-1100 Series comes in the following configurations: System Slots Peripheral Slots PSU(s) Monitor PICMG c