Adlink cPCIS-ET2600 Series Bedienungsanleitung

cPCIS-ET2600 Series 4U Height Wide Temperature Range Subsystem for 3U CompactPCI Modules User’s Guide

4 • Introduction This page intentionally left blank.

Backplane • 5 2 Getting Started In this chapter, we will describe the unpacking procedure of the subsystem and CompactPCI board and power supply unit

6 • Backplane System slots usually have obvious indicators (e.g. red card guide rail, triangle mark enclosing the slot number on the backplane, etc

Backplane • 7 The handle on CompactPCI cards and PSUs ensures simple and safe installation and removal. Please follow the procedures below to install

8 • Backplane To remove the module, press the release button (if necessary), and reverse steps 1 through 5 above. Fully Latched Handle En

Backplane • 9 2.3 RTM (Rear Transition Module) Installation The installation and removal procedures for a RTM are the same as those for CompactPCI b

10 • Backplane 3 Backplane In this chapter, we will describe the backplane for the cPCIS-ET2600 Series subsystems. The following table specifies the

Backplane • 11 Mechanical Drawing cBP-3208[R]Front View1 - P2 1 - P1 8 - P2 8 - P1

12 • Backplane cBP-3208[R] Rear View 1 - P2 Optional Rear I/O: 2 - P2 to 8 - P2

Backplane • 13 Pin Assignment ¾ [1 – P1] System Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND24 GND AD[1] +5V V(I/O)

Copyright 2013 ADLINK Technology, Inc. All Rights Reserved. Manual Rev. 1.00, January 2, 2013 Part No.: 50-15088-2000 The information in this do

14 • Backplane ¾ [1 – P2] System Slot Pin Z A B C D E F 22 GND GA4 GA3 GA2 GA1 GA0 GND21 GND CLK6 GND NC NC NC GND20 GND CLK5 GND NC NC N

Backplane • 15 ¾ [2 – P1] / [8 – P1] Peripheral Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND 24 GND AD[1] +5V V(I/O) A

16 • Backplane ¾ CN1 / CN2 – ATX Power Connector Pin Signal Pin Signal 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON_L 5 GND 15 GN

Backplane • 17 3.2 cBP-3206[R] Backplane The cBP-3206[R] is a 3U CompactPCI 32-bit backplane with optional rear I/O (designated by an “R” suffix). Th

18 • Backplane Mechanical Drawing cBP-3206[R]Rear ViewcBP-3206[R]Front View1 - P21 - P16 - P26 - P1CN1 CN2 JP8 - JP101 - P2 Opt. Rear I/O: 2 - P

Backplane • 19 Pin Assignment ¾ [1 – P1] System Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND24 GND AD[1] +5V V(I/O)

20 • Backplane ¾ [1 – P2] System Slot Pin Z A B C D E F 22 GND GA4 GA3 GA2 GA1 GA0 GND21 GND CLK6 GND NC NC NC GND20 GND CLK5 GND NC NC N

Backplane • 21 ¾ [2 – P1] – [6 – P1] Peripheral Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND 24 GND AD[1] +5V V(I/O) A

22 • Backplane ¾ CN1 / CN2 – ATX Power Connector Pin Signal Pin Signal 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON_L 5 GND 15 G

Backplane • 23 3.3 cBP-3061 Power Backplane The cBP-3061 is a PICMG 2.11 CompactPCI 3U 47-pin power backplane for one power module. It is used by the

Table of Contents • iii Table of Contents How to Use This Manual...v 1 Introduction ...

24 • Backplane Pin Assignment ¾ CN1 – Power Sense Connector Pin # Signal Name 1 V1_Sense 2 GND_S 3 V2_Sense 4 V3_Sense 5 NC ¾ CN2 – Power Sense

Backplane • 25 ¾ CN4 – Modular Power 47P Connector Pin Signal Pin Signal 47 ACL/-DC IN 31 GA2 46 ACN/+DC IN 30 V1 SENSE 45 CGND 29 V1ADJ 44

26 • Backplane ¾ CN7 –AC/DC in Let Connector Pin # Signal Name 1 ACN/DC+ 2 ACL/DC- 3 CGND ¾ CN8 – IPMB Connector Pin # Signal Name 1 IPMB_SC

Backplane • 27 3.4 cBP-3062 Power Backplane The cBP-3062 is a PICMG 2.11 CompactPCI 3U 47-pin power backplane for two power modules. It is used by th

28 • Backplane Pin Assignment ¾ CN1 / CN2 – Modular Power 47P Connector Pin Signal Pin Signal 47 ACL/-DC IN 31 GA2 46 ACN/+DC IN 30 V1 SENS

Backplane • 29 ¾ CN5 – Power Sense Connector Pin # Signal Name 1 V1_Sense 2 GND_S 3 V2_Sense 4 V3_Sense 5 NC ¾ CN6 –Connector Pin # Signal Name

30 • Backplane ¾ CN9 / CN10 – ATX Power Connector Pin Signal Pin Signal 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON_L 5 GND 15

Cooling System • 31 4 Cooling System The cPCIS-ET2600 Series subsystems with CompactPCI PSUs are equipped five front-access hot swappable low noise fa

32 • Cooling System 2. After cleaning or replacing the filter, place it back in position and re-attach the filter cover. 3. Remove the screws atta

Cooling System • 33 4.2 Fan Alarm: Fan Removal and Replacement The embedded alarm board monitors temperature & fan status. Should a fan become d

iv • Table of Contents 4.3 Temperature Alarm...34 4.4 Fan Specifications ...

34 • Cooling System 4.3 Temperature Alarm When the subsystem's internal temperature exceeds 50°C, the TEMP LED will flash and an audible warning

Power Supply Unit • 35 5 Power Supply Unit The cPCIS-ET2600 Series subsystems are equipped with ADLINK’s cPS-P325/AC CompactPCI power module. 5.1 Co

36 • Power Supply Unit Input Characteristics • Input Voltage: Typ. 90-264VAC • Power Factor Correction: Meets Harmonic Correction EN 61000-3-2. •

Power Supply Unit • 37 • Noise & Ripple: 60 mV@5V and 3.3V output; 120mV@.± 12V output. • OVP: Built-in at all outputs. • Adjustability: Avail

38 • Power Supply Unit This page intentionally left blank.

Specifications • 39 6 Specifications 6.1 Features • Standard 19” Rack-mount 3U CompactPCI form factor (4U height). • Board Space: o Supports both f

40 • Specifications 6.3 Environmental • Operating Temperature: -20°C to 50°C (Supports operation up to 70°C but with derating above 50°C. Power effi

Specifications • 41 Mechanical Drawing

42 • Specifications This page intentionally left blank.

Important Safety Instructions • 43 Important Safety Instructions Read and follow all instructions marked on the product and in the documentation befo

How to Use This Manual • v How to Use This Manual This manual is designed to help you use the cPCIS-ET2600 series 3U CompactPCI Subsystem . It is divi

44 • Important Safety Instruction z Lithium Battery provided (real time clock battery) “CAUTION – Risk of explosion if battery is replaced by an inc

Getting Service • 45 Getting Service ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan Tel:

46 • Getting Service ADLINK Technology, Inc. (French Liaison Office) Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France Tel: +33 (0) 1 60 12

vi • Introduction This page intentionally left blank.

Introduction • 1 1 Introduction 1.1 Product Definition The cPCIS-ET2600 wide temperature range subsystem is rack mountable, 4U in height, and designed

2 • Introduction 1.2 Mechanical Drawing R

Introduction • 3 1.3 Configurations The cPCI-ET2600 Series comes in the following configuration: system slots peripheral slots PSU(s) monitor PICMG