Adlink nanoX-TC Bedienungsanleitung PDF herunterladen (Seite 40)

nanoX-TC User’s Manual Page 40

8.4.6 Super IO Configuration

You can use this screen to select options for the Super IO settings. Use the up and down <

Arrow > keys to select an item. Use the < + > and < - > keys to change the value of the

selected option. The settings are described on the following pages. The screen is shown

below.

Serial Port 0,1 Configuration

Set Parameters of Serial Port 0,1. Set this value to Enabled/Disabled.

Change Settings

This option specifies the base I/O port address and interrupt request address of serial port

0,1. Options shown below.

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 61 62

User’s Manual 1
Revision History 2
Table of Contents 3
Preface 5
Conventions 6
1 Introduction 7
2 Specifications 8
2.3 Audio 9
2.4 LAN 9
2.5 Multi I/O 9
2.6 Super I/O 9
2.7 SDIO/MMC Extension 10
2.8 Operating Systems 10
2.10 Power Specifications 10
2.11 Power Consumption 11
2.12 Ordering Codes 11
3 Functional Diagram 12
4 Mechanical Dimensions 13
Type 10 Pinout 14
5.1 COM Express 14
5.2 Pin Definitions 15
5.3 Signal Descriptions 16
Signal Descriptions (cont’d) 17
DDI0_DDC_AUX_SEL 19
DDI0_CTR LCLK_AUX+ 19
DDI0_CTRLDATA_AUX 19
Signal Description Legend 20
6 Embedded Functions 21
6.2 GPIO 22
6.3 Hardware Monitoring 23
7 System Resources 24
7.3 Legacy I/O Map 25
Legacy I/O Map (cont’d) 26
PIC Mode 27
APIC Mode 27
APIC Mode (cont’d) 28
8 BIOS Setup Utility 30
8.3 Main Setup 32
8.4 Advanced BIOS Setup 33
8.4.1 ACPI Settings 34
CPU Configuration Settings 34
Enable Hibernation 34
ACPI Sleep State 34
8.4.2 CPU Configuration 35
Hyper-Threading Technology 35
Intel® SpeedStep tech 35
Limit CPUID Maximum 36
Intel® Virtualization Tech 36
Intel® C-STATE tech 36
Enhanced C1~C4 36
Wake On LAN 37
8.4.5 H/W Monitor 39
Change Settings 40
Console Redirection 41
Console Redirection Settings 41
8.4.8 Network Stack 43
8.5 Chipset Configuration 44
Boot Display Configuration 45
Boot Display Device 45
Flat Panel Type 45
LVDS Backlight Control 45
Audio Controller 46
SMBus Controller 46
PCI Express Root Ports 46
8.6 Boot Setup 47
8.7 Security Setup 48
8.8 Save & Exit 49
Viewing BIOS Checkpoints 51
9.1 Status Code Ranges 52
9.2 Standard Status Codes 52
PEI Status Codes 53
PEI Status Codes (cont’d) 54
PEI Beep Codes 55
DXE Status Codes 55
DXE Status Codes (cont’d) 56
DXE Beep Codes 57
ACPI/ASL Status Codes 57
Getting Service 60

Kommentare zu diesen Handbüchern

Keine Kommentare

Adlink nanoX-TC Bedienungsanleitung Seite 40

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Adlink nanoX-TC