Adlink nanoX-TC Bedienungsanleitung Seite 53
- Seite / 62
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Page 53 Express-IA533 User’s Manual Page 53 Express-IA533 User’s Manual nanoX-TC User’s Manual Page 53
PEI Status Codes
Status Code Description
0x0 Not used
Progress Codes
0x10 PEI Core is started
0x11 Pre-memory CPU initialization is started
0x12 Pre-memory CPU initialization (CPU module specific)
0x13 Pre-memory CPU initialization (CPU module specific)
0x14 Pre-memory CPU initialization (CPU module specific)
0x15 Pre-memory North Bridge initialization is started
0x16 Pre-Memory North Bridge initialization (North Bridge module specific)
0x17 Pre-Memory North Bridge initialization (North Bridge module specific)
0x18 Pre-Memory North Bridge initialization (North Bridge module specific)
0x19 Pre-memory South Bridge initialization is started
0x1A Pre-memory South Bridge initialization (South Bridge module specific)
0x1B Pre-memory South Bridge initialization (South Bridge module specific)
0x1C Pre-memory South Bridge initialization (South Bridge module specific)
0x1D – 0x2A OEM pre-memory initialization codes
0x2B Memory initialization. Serial Presence Detect (SPD) data reading
0x2C Memory initialization. Memory presence detection
0x2D Memory initialization. Programming memory timing information
0x2E Memory initialization. Configuring memory
0x2F Memory initialization (other).
0x30 Reserved for ASL (see ASL Status Codes section below)
0x31 Memory Installed
0x32 CPU post-memory initialization is started
0x33 CPU post-memory initialization. Cache initialization
0x34 CPU post-memory initialization. Application Processor(s) (AP) initialization
0x35 CPU post-memory initialization. Boot Strap Processor (BSP) selection
0x36 CPU post-memory initialization. System Management Mode (SMM) initialization
0x37 Post-Memory North Bridge initialization is started
0x38 Post-Memory North Bridge initialization (North Bridge module specific)
0x39 Post-Memory North Bridge initialization (North Bridge module specific)
0x3A Post-Memory North Bridge initialization (North Bridge module specific)
0x3B Post-Memory South Bridge initialization is started
0x3C Post-Memory South Bridge initialization (South Bridge module specific)
0x3D Post-Memory South Bridge initialization (South Bridge module specific)
0x3E Post-Memory South Bridge initialization (South Bridge module specific)
0x3F-0x4E OEM post memory initialization codes
0x4F DXE IPL is started
- User’s Manual 1
- Revision History 2
- Table of Contents 3
- Preface 5
- Conventions 6
- 1 Introduction 7
- 2 Specifications 8
- 2.3 Audio 9
- 2.4 LAN 9
- 2.5 Multi I/O 9
- 2.6 Super I/O 9
- 2.7 SDIO/MMC Extension 10
- 2.8 Operating Systems 10
- 2.10 Power Specifications 10
- 2.11 Power Consumption 11
- 2.12 Ordering Codes 11
- 3 Functional Diagram 12
- 4 Mechanical Dimensions 13
- Type 10 Pinout 14
- 5.1 COM Express 14
- 5.2 Pin Definitions 15
- 5.3 Signal Descriptions 16
- Signal Descriptions (cont’d) 17
- DDI0_DDC_AUX_SEL 19
- DDI0_CTR LCLK_AUX+ 19
- DDI0_CTRLDATA_AUX 19
- Signal Description Legend 20
- 6 Embedded Functions 21
- 6.2 GPIO 22
- 6.3 Hardware Monitoring 23
- 7 System Resources 24
- 7.3 Legacy I/O Map 25
- Legacy I/O Map (cont’d) 26
- PIC Mode 27
- APIC Mode 27
- APIC Mode (cont’d) 28
- 8 BIOS Setup Utility 30
- 8.3 Main Setup 32
- 8.4 Advanced BIOS Setup 33
- 8.4.1 ACPI Settings 34
- CPU Configuration Settings 34
- Enable Hibernation 34
- ACPI Sleep State 34
- 8.4.2 CPU Configuration 35
- Hyper-Threading Technology 35
- Intel® SpeedStep tech 35
- Limit CPUID Maximum 36
- Intel® Virtualization Tech 36
- Intel® C-STATE tech 36
- Enhanced C1~C4 36
- Wake On LAN 37
- 8.4.5 H/W Monitor 39
- Change Settings 40
- Console Redirection 41
- Console Redirection Settings 41
- 8.4.8 Network Stack 43
- 8.5 Chipset Configuration 44
- Boot Display Configuration 45
- Boot Display Device 45
- Flat Panel Type 45
- LVDS Backlight Control 45
- Audio Controller 46
- SMBus Controller 46
- PCI Express Root Ports 46
- 8.6 Boot Setup 47
- 8.7 Security Setup 48
- 8.8 Save & Exit 49
- Viewing BIOS Checkpoints 51
- 9.1 Status Code Ranges 52
- 9.2 Standard Status Codes 52
- PEI Status Codes 53
- PEI Status Codes (cont’d) 54
- PEI Beep Codes 55
- DXE Status Codes 55
- DXE Status Codes (cont’d) 56
- DXE Beep Codes 57
- ACPI/ASL Status Codes 57
- Getting Service 60
Verwandte Produkte und Handbücher für Hardware Adlink nanoX-TC
Hardware Adlink nanoX-TCR Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Hardware Adlink nanoX-BASE Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Hardware Adlink LEC-BTS Bedienungsanleitung
(22 Seiten)
(22 Seiten)
Hardware Adlink LEC-iMX6 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Hardware Adlink LEC-3517 Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Hardware Adlink LEC-BASE R1 Bedienungsanleitung
(30 Seiten)
(30 Seiten)
Hardware Adlink ETX-BT Bedienungsanleitung
(70 Seiten)
(70 Seiten)
Hardware Adlink ETX-CV Bedienungsanleitung
(86 Seiten)
(86 Seiten)
Hardware Adlink ETX-PVR Bedienungsanleitung
(68 Seiten)
(68 Seiten)
Hardware Adlink ETX-Proto Bedienungsanleitung
(38 Seiten)
(38 Seiten)
Hardware Adlink MXC-6300 Series Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Hardware Adlink MXC-6000 Series Bedienungsanleitung
(100 Seiten)
(100 Seiten)
Hardware Adlink MXC-2300 Bedienungsanleitung
(76 Seiten)
(76 Seiten)
Hardware Adlink MXE-5400 Bedienungsanleitung
(88 Seiten)
(88 Seiten)
Wolf 650G Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein Wolf 650G.
Wir stellen 1 PDF-Handbücher Wolf 650G zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Spezifikationen
Kommentare zu diesen Handbüchern